Fees and billing
Fees and the builder address
How you earn
Every order your clients place carries a builder code: an address and a fee rate. Hyperliquid pays that fee out of the fill to the builder address. That address is your builder address. In the console the fee is called your trading fee.
You earn only while the platform routes fees to you (see Billing). The fee is charged on both sides of a trade: when a position opens and when it closes. It applies to maker and taker fills. Clients also pay Hyperliquid's own fee on top of yours.
Setting the rate
In Fees, choose a common rate (0.03%, 0.05% or 0.10%) or enter your own under "Custom". You can use up to three decimals, in steps of 0.001%. The maximum is 0.10%, which is Hyperliquid's cap for perpetuals. Enter 0 to charge no fee.
| You enter | Per $1,000 order, per fill |
|---|---|
| 0.01% | $0.10 |
| 0.03% | $0.30 |
| 0.05% | $0.50 |
| 0.10% | $1.00 |
Hyperliquid's base taker fee is 0.045% ($0.45 on the same order). Lower fees are easier for active clients to accept. Starting low is safer than starting high, because raising the fee later makes every client approve again (see below).
The 100 USDC builder requirement
Hyperliquid requires the builder address to hold at least 100 USDC of account value on Hyperliquid (perps account). Without it, Hyperliquid rejects orders that carry your builder code.
What to do:
- Choose a wallet you control as your builder address. Use a separate wallet from your login wallet if you can. It only receives fees, and clients never see its key.
- Deposit at least 100 USDC into that address's Hyperliquid perps account.
- In Fees, select Save and check this address. The console reads the account value from Hyperliquid and shows "This address can receive fees" or "This address cannot receive fees yet".
- Keep the balance above 100 USDC. If it drops below, clients' orders can fail.
The check does not stop you from saving, but until the requirement is met your site cannot take orders that carry a fee. The 100 USDC is your own money and stays yours. You can also select Use connected wallet to fill in the address of the wallet you are signed in with.
Fees you earn accrue to the builder address on Hyperliquid. You claim them from Hyperliquid, not from the platform.
The approval prompt your clients see
A client must approve a builder before the builder can charge. The first time they set up trading on your site, their wallet shows a Hyperliquid message approving your builder address up to your maximum rate. This is one signature. It moves no money and costs no gas. The client can approve a lower maximum later to reduce what you may charge.
What happens when you raise fees
Clients approved a maximum. If you raise the rate above it, or change the builder address:
- Their next order fails until they approve again.
- The terminal asks them to approve the updated fee, with the new rate.
- Some clients will not approve again and will leave. Expect churn.
The console warns you before you publish such a change ("Your trading fee goes up" or "The fee goes to a new address"). You must confirm with Publish and ask clients to approve. Lowering a fee needs no new approval. Orders already resting on the book keep the builder they were placed with.
What happens when fees switch to the platform
If your plan is unpaid (Free, lapsed or cancelled), the platform's builder address replaces yours. Your clients see the approval prompt once, for the platform's address. When you pay again, it switches back and they approve your address again (or still have the old approval). Details and timing: Billing.
The rate while you are on Free
The platform charges your configured rate, but never less than 0.05%. Setting your fee to 0 does not avoid the platform's commission while you are on Free or unpaid. On Pro, 0 means no fee.
Rules summary
| Situation | Who is paid | Rate |
|---|---|---|
| Pro | You | Your rate |
| Pro, renewal late (grace, 3 days by default) | You | Your rate |
| Free, lapsed or cancelled | Platform | The higher of your rate and 0.05% |
| Platform admin sets a fee kill switch | Nobody | 0, or lower than the rate above |
| Pro, but no builder address set | Nobody | 0 |
Disclosing the fee
Ask counsel whether your terms must name who receives the fee. The operator agreement explains that fees go to the platform when you are unpaid. Your clients should be told there is a trading fee, who receives it, and which rate applies. The hosted legal pages and the client help page on your site state this from your live settings. The terminal shows the fee on the order ticket before submission.
Hyperliquid referral code
If the platform has set a Hyperliquid referral code, your site registers it for each client whose Hyperliquid account has no referrer yet. It happens once, in the background, without a wallet prompt. The client gets Hyperliquid's referral discount on fees, and Hyperliquid pays the code's owner (the platform) a share of Hyperliquid's own fee. Nothing is added to what your clients pay and your builder fee is unchanged. The terms your clients accept say this. A client who already has a referrer is left alone.